Anti Theft alarm Wiring, Pink wire and grey wire uses.

This video still helps people! Thank u sir. I was abaout to rip off my aalarm, but you explained it.saved me time and money

Thank you sir this helped me a lot, i converted a car alarm to work on a motorcycle using your information. Cheers 👌🏻

Very useful Info , they write flame-out line ! Grey / pink…… Was wondering The use ? , wanted some sort of immobilising Working from this device , you clarified the purpose, thanks……

I hope you can shine some light on my problem. I have the sabvaton 72150 controller that I want to add an alarm to but the seller from Alibaba forgot to add the anti theft plugs. My alarm has two plugs. One plug has red & black for (power), the other plug has three wires, Orange - for ignition (key), Brown- connect to blue phase wire for (mtr signal input) and blue to anti-theft. The problem is my controller does not have the plugs. I read in a forum I can ground the blue wire because it will complete the mtr signal (brown to phase) wire during activate ( alarm sounding) what you think? Thx for any help you can provide.

I have a 2016 zx10r, in the instructions I'm supposed to cut the CDI or flameout wire & connect the pink &gray wire to either end. If so what color is the CDI or flameout wire.

Hi a have scooter in ignition key 2 wire is there color red and (orange)not sure more dark in orange. I tap orange wire of alarm in orange color and blue wire of alarm in push start positive. it's is correct? Remote start/off is working.. it's safe to tap orange wire there or no? 2nd question where to tap pink/gray color of alarm?

where do i connect the grey and pink wires..My bike is TVS HLX 150

How to get negative 12v potential through blue wire as my Yamaha's starter relay working on negative potential

Good explanation with prove.. thanx bro

Nice work bro. It was a good explanation. I was looking here and there for to find what is the purpose of this two wires. I need to use this kind of alarm with my car central lock system. so,I need to trigger any signal for lock and unlock the central lock. it seems possible with these two wires. If so how can i connect it with central lock system. thank you

hi i have the same alarm, i wanna know if we can turn off the sound when activating the alarm or dactivating it.. or minize the sound.. thank you..

I got the basic idea my friend thanks. But would it make a difference if my bike has 4 ignition coil? Plug it in one of them? What about kill switch? Sorry im not electrically inclined. Thanks in advance for your help

The gray and pink wires are for the option of turning the engine off "Anti Hijack Mode", so these wires are very important and should be connected in series along the Engine Stop Switch circuit.

Hi a need some help , there are Two Black wires in my alarm , one comes from the harness along with the Red(possitive) and there is one more Black wire that comes directly from the alarm brain , which is the corect one for the (-) negative battery pole ?

Great Indian Jugaad . Thanks to this video. Its a great help for me. Soon, I am going to install this to my scooter. Kindly check if my proposed diagram is correct. On of each yellow wire, I will connect it to the positive side of my flasher wires (one at left and right flasher). For the Orange wire, I will connect it to the negative wire that supplied the key ignition switch. For Blue wire, I will connect it to the positive of the push button then lastly, I select one of the either gray or pink and I will connect it to NC relay at 86 then at 85, I will connect it to the positive supply of the battery. I will cut the connection of the ignition switch wire then I will attached it to 87a and 30 of the relay. Kindly comment plz...Tnx

is the connection same with yamaha exciter 150i fuel injected? thanks in advance

i’m not sure if i understand it right, if you arm the device the continuity of pink and grey disconnect and if unarmed the continuity returned?? it’s right??

Ever got to doing that keylessgo stuff? As in removing the ignition key all together?

That's correct, the Grey and Orange cable with an NC Relay can be used as an engine cut off switch, Connect the 30 & 87a Pins to the engine cut off cables.

I have a tvs star sport bike and i instol the alaram but where i connect white and greay wire. Pls help me