unscrew the broken bolt without drilling and welding, simple trick

I've never encountered a broken bolt stud that could be unscrewed that easily. Usually the studs break because they are stuck so tight that the force required to loosen them is greater than the strength of the bolt.

Стакими ногтями его можно было просто ногтем выковырять)))

Те,кто сталкивался с подобной проблемой,знают,что этот простой трюк работает крайне редко .

In my forty plus years as a service engineer I would say I have removed maybe 50% of bolts like that but normally they are to tight to knock around, if you have a bolt that is snapped a good way down the hole a good trick is if you have a Lathe get a socket cap screw the same size and thread as the snapped one put it in the Lathe and drill a hole through the centre then put it in the hole were the snapped bolt is then using the same drill bit drill through the snapped bolt it allows you to get the dead centre you can then put penetrating oil down the hole and use an easy out. I always keep a selection of different size bolts ready to use works a treat.

Показан очень сложный случай - обломок свободно люфтит. Вот, если, обломок чуть прихватило коррозией, или на герметике - тогда, вообще, раз плюнуть!)))

Когтями этого мастера можно выкрутить любой болт 🐾🤙🏻🔥

Backwards turn drill bit will often spin those right out. The punch method I've used often as well.

I generally go with the concept that if it is liquid it cannot be stuck. 🙂 Seriously, anybody who is working with steel bolts in aluminum castings should be applying an anti seize when assembling the parts. It will also help to prevent stripout when tightening the bolts.

Это просто фантастика. Жалко что такие заломыши встречаются в одном случае из ста из за того что это был говноболт. Обычно это прикипевшие, приржавевшие или обломанные из за того что не по резьбе закручивались и вот там всë это не работает. А вот удаление такого заломыша как в видео я бы и снимать постеснялся.

Болтающийся остаток болта можно было выкрутить выверткой левой и не долбить полчаса. А с такими когтями можно было прям ими как отвёрткой крутить 😂

This solution is effective only in one case: when the bolt breaks off while being tightened, and when it does not rest against the bottom, after which, usually, the thread “unwinds” and changes pitch if the tightening was carried out without observing the torque. therefore, you first need to make sure that the thread has not “unraveled” on the broken edge. otherwise, when turned out, not only the pitch, but also the alignment will be destroyed on the upper remainder of the thread.

Amazing !!!! what an art it is to remove and fix that kind of stuff. Excellent !!!

Loved how he covered the chain with the rag and then blew everything in deeper with the air

I normally use a center punch to: A. Shock the broken bolt, THEN: B. use a left hand drill bit and SLOWLY drill at the center punch mark INTO the broken bolt. MOST of the time, the bit will bind into the broken part and back it out for you. If not, then you can use an extractor in the hole made by left hand drill!. TIP: A bit of grease will catch the shavings and keep them out of the engine.

Hi, I have an 8 in wide drawer in my tool box that is dedicated to small, pointy tools like this . Chissels of all kinds of faces and many more dedicated to "Hey, get Dean, he can get them out, LOL I'm retired now but on occasion the logging shop still will call every once in a while to help them out. Hmmm, Retirement sucks, LOL.

Left-handed drill bits work real good

He could have used his finger nails instead of the 2nd hand ground down pliers.

What good does it do to cover the top of the tapped when the cuttings are are falling down into the engine? oh, I see the air will blow everything further in.

You are creativity It's true I am a new subscriber to your channel and this is my first comment in this video that deserves all the appreciation I wish you success and lasting success, God willing and his blessings Your friend Hani from Egypt from Cairo

Если заломыш не прикипел и так свободно болтается, он бы не сломался. Ролик - "сказка"